Category: part

  • Triumph Vitesse / GT6 rear rotoflex set up shims

    I was very pleased to track down a supply of shims to rebuild the rear hubs on my Triumph Vitesse.

    Do you remember Jigsaw Racing?  Well their workshop may have closed down but you can still buy stuff via their eBay store.

    Now I just need to get my workshop built so my Vitesse can receive some long delayed attention.

  • TR7 removable hardtops

    I bought a detachable hardtop for my TR7 convertible to make it just a little more practical.

    It has done a good job of keeping the rain and snow off me.  It turns out that my hardtop is made by Honeybourne Mouldings rather than Lenham.   Honeybourne hardtops are available new again after the firm reintroduced them.  Apparently the design had to be renewed as the original moulds were no longer up to the job.

    Triumph TR7 Honeybourne Moulding hardtop
    Honeybourne TR7 hardtop

     The windows are different on a Lenham as shown below.

    Lenham hardtop

    The rear window in a Lenham is the same size amd shape as in the TR7 fixed head.  Before I realised I had a Honeybourne rather than a Lenham I bought a heated rear windows from a TR7 fixed head as I fancied having a demistable back window.

    Both Lenham and Honeybourne hardtops fix to the car in the same way,

    Triumph TR7 Honeybourne Moulding hardtop view of undderside

    clipping to the header rail at the front and by J bolts to the hood frame near the B post of the car.

    Alternative hardtops

    A German design.

    Lenham

    Lenham hardtop advert
    Lenham hardtop advert

    DIY Amerian

    DIY Amerian hardtop 1
    DIY Amerian hardtop 2

    A DIY Amerian made hardtop.

    Smooth Line

    Smooth Line hardtop for Triumph TR7
    Smooth Line hardtop

    Smooth Line hardtop from USA. Still being made as I write this.
    http://www.smoothline.com/triumph.php

    Smooth Line hardtop exterior

    Triumph TR 7-8 Hardtop with Haartz Vinyl Exterior view above. Triumph TR 7-8 Hardtop Interior view below.

    Smooth Line hardtop interior

    SnugTop

    SnugTop hardtop 1

    The SnugTop design as made in the USA.

    SnugTop hardtop 2 for Triumph TR7
    SnugTop hardtop 2

    Extract from Motor

    The 3rd May 1980 edition of Motor magazine contained details of two new accessories for the TR7. A roll over protection bar and a detachable hardtop.

    Cover for TR7

    QUICK OFF the mark, Lenham have introduced a detachable hard-top for the Triumph TR7 convertible. Made from glass fibre the roof is supplied in black or may be painted to match the car. The tinted rear window has heating elements, the interior is fully lined with cloth and the side windows open The roof can be supplied with a tilt or take-out Amilite sun-roof (as can all Lenham hardtops). Prices with VAT are: £345 and £488.75 with Amilite sunroof. Lenham Motor Co. Limited, 47 West Street, Harrietsham, Kent.

  • How to identify those nuts and bolts etc

    Over the years manufacturers have produced guidance as to the fasteners to use on their vehicles. BMC produced a Fastener Decode Booklet. Parts books very often seem to show a picture of the fastening or give a part number without a description of the size and length.  I know traders have worked out what fits where but as somebody with a lot of spare nut and bolts I like to be able to use something from my existing stock. I have collected several documents and webpages over the years and thought it would usegful to gather them into one place here.

     BMC Fastener Decode Booklet

     

    BMC Fastener Decode Booklet cover

     Here is a sample page. You can download the whole Fastener Decode Booklet from here.

    BMC Fastener Decode Booklet sample page

    BMC Fastener Decode Booklet sample page

    Standard Triumph Hardware Catalogue

    Standard Triumph Hardware catalogue front cover
    cover of Standard Triumph Hardware catalogue
    Standard Triumph Hardware catalogue introduction
    Standard Triumph Hardware catalogue introduction
    Standard Triumph Hardware catalogue contents page
    Standard Triumph Hardware catalogue contents page

    The Standard Triumph factory produced a useful catalogue of the fastenings etc used in their vehicles.  As many of the components were used in many different vehicles from the manufacturer over the years it is still of use to many cars in the era after the Standard brand had gone. You can download a copy of the Standard Triumph Hardware catalogue here.

    April 2005- JAGUAR PART NUMBER APPLICATION IN RELATION TO THE SIZE AND TYPE OF BOLT – SETSCREW

     

    Post XK models pre British Leyland era. Early middle 1960’s
    For Example:
    Part number: UFB 131 – 16R
    UF = Unified Thread
    B = Bolt
    1 = No technical meaning known
    31 = .31 of an inch in decimal terms or 5/16 in fraction being the diameter of the bolt shank
    16 = 16 x 1/8 of an inch being 2 inches the length of the bolt shank
    By replacing the ‘B’ to a ‘S’ being UFS this would determine a setscrew NOT bolt i.e. with thread the entire length of the Shank
    And UCB means Unified Coarse Bolt UCS means Unified Coarse Set Screw Fine and Coarse is the pitch of the thread (TPI) Threads per inch
    The previously illustrated part number used as an example could be superseded by a new part number without the part changing under the British Leyland Standard LG5.06.01 December 1969
    For Example:
    Part number: BH 605161/J

    B = Bolt
    H = Hexagonal
    6 = UNF thread
    05 = 5/16 of an inch being the diameter of the bolts shank
    16 = 16 x 1/8 of an inch being 2″ the length of the bolt shank
    When the bolt is replaced by SH it means it would be a set screw. By replacing the 6 to a 5 it would determine that it is a coarse thread UCS.
    Similar applies with nuts:
    UFN = Unified Fine Thread
    UCN = UCN Unified Coarse Thread
    The same workings apply as a bolt or set screw.

    April 2005- BRITISH LEYLAND FASTENERS CODING SYSTEM

     

    Identifying letters

    As far as possible, these describe the part e.g. NH is nut, hexagon, BH is bolt,hexagon. Where appropriate, these identifying letters are also related to the material grades employed by the individual components they represent. See Appendix A for further details in this respect.

    First digit

    This denotes the Thread Series as below 1 ISO Metric Coarse Pitch 2 ISO Metric Fine Pitch 3 Whitworth thread 4 BSG thread 5 Unified Coarse thread 6 Unified fine thread 7 BA thread 8 American Numbered Coarse thread 9 American Numbered Fine thread The first digit applications for non-threaded fasteners and other particular types of fastener component are detailed separately in LGS.06.07 and LGS.08 etc. Note For combination thread studs, the metal end thread series of the stud shall be the basis of coding for the first digit.

    Second and third digits

    These usually indicate the nominal diameter of the part, in millimeters if the part is metric in % in if the part is an inch thread form, and if the part has a numbered diameter, they indicate the number directly, e.g. 12mm is represented by 12. 1in by 16 4BA by 04. The second and third digit applications for non-threaded fasteners and other particular types of fastener component are detailed separately in LGS.06.07 and LGS.06.08 etc.

    Fourth and fifth digits

    These usually indicate the nominal length of the component as indicated below. These nominal length increments of coding for the various types of fastener have been carefully selected to give the maximum coverage possible within a logical coded system although it must be appreciated that this imposes certain limitations. For example metric screws greater than 99mm long cannot be coded, nor can short metric studs or bolts which have nominal lengths which are not in exact 5mm increments. Should such components be required in these sizes it is recommended that they be added to existing individual company stock lists until they can be included in a common Group part numbering system for miscellaneous standard parts.

    Bolts

    In this instance, the digits indicate the nominal length of the component, in 5mm increments if it is a metric fastener, 1/8in increments if it is an inch size fastener 1/32 in increments for BA and America Numbered Thread Series fasteners.

    Screws

    In this instance, the digits indicate the nominal length of the component, in 1mm increments if it is a metric fastener, 1/8in in increments if it is an inch size fastener 1/32 in increments for BA and American Numbered Thread Series Fasteners.

    Studs

    In this instance, the digits indicate the nominal length (see note below) of the component, in 5mm increments if it is a metric fastener, 1/8in increments if it is an inch size fastener, 1/32in increments for BA and American Numbered Thread Series fasteners. Note: For Unified studs the nominal length shall be the overall length as laid down in BS2693. For Metric studs the nominal length shall be the standout length as laid down in ISO R/225 and in BS4439.

    Nuts

    The fourth digit represents the basic type of material (steel, brass, etc.) and the fifth digit indicates the various grades or other classifications (e.g. tensile strength) of these individual materials. See also Clause 3 of Appendix A.In certain instances where this nut material code cannot be satisfactorily applied (e.g. for piercenuts where one common thread diameter may be used with varying external dimensional features) the alternative coding is given on the individual part number sheet.

     

    Fourth digit

    This represents the basic type of material as given below:
    0-Steel
    1-Brass
    2-
    3-
    4-
    5-
    6-
    7-
    8-
    9-

    Fifth digit

    This represents the respective grade or other classification of the individual basic materials as laid down in the following clauses.

    Steel Nuts (having a fourth digit of 0)

    For steel nuts the fifth digit code given below in Table 1 comprises an ‘equivalent material’ grading system which is formulated so as to provide one basic set of fifth digits to cater for the existing standard grades of steel for nuts in the various recodnised standard thread series. It is based primarily on the metric grading system outlined for nuts in BS3692 (‘ISO Metric precision hexagon bolts, screws and nuts’) as this should in time form the ultimate grading system for steel nuts

    Notes:

    1. The fifth digits 1,4 and 6 (see tables 1 and 2) apply to nuts which are normally used in conjunction with the following types of fasteners.
    Fifth digit 1 – low tensile fasteners such as machine screws and other small low tensile bolts such as BA and American Numbered types.
    Fifth digit 4 – medium tensile (precision) fasteners. The majority of nuts currently used fall within this category.
    Fifth digit 6 – high tensile fasteners for use in special design applications.
    2. For further more detailed information regarding the various grades of ruts, the respective BS specification should be consulted.

     

    Triumph fastener part number system

    (Information courtesy of John Kipping)
    Part numbers for nuts, bolts, & washers use Triumph’s system indicating the size & type, shown in the chart below.
    A nut with part # YN2912 is a 9/16″ UNF nyloc nut.
    A bolt with part # KT504 is a No. 10 UNF, countersunk slotted screw, 1/2″ in length.
    A washer with part # WL0208 is a split-ring lockwasher.


    Nuts Bolts
    Two-letter prefix gives type of nut.

    Thread size is indicated by the last two digits.

     Two-letter prefix gives type of bolt.

    Length of bolt is indicated by the last two digits, in eighths of an inch (up to 49).

    Thread type is always UNF unless the second digit from the right is 5, in which case the thread will be UNC.

    Thread size is indicated by the first digit(s)

    (This digit may or may not be preceded by a 0, but the table below shows leading zeroes for
    reference.)

    PrefixType of nut PrefixType of bolt
    HNplain nut HUsetscrew (threaded all the way to the head)
    YNnyloc nut HBbolt
    JNjam nut (i.e., half-thickness) KXcountersunk crosshead
    TNthin type nyloc PTpan head slotted
      PXpan head crosshead
    Last 2 digitsThread size First digit(s)Thread size
    03No. 6 UNF 03No. 6 UNF
    04No. 8 UNF 04No. 8 UNF
    05No. 10 UNF 05No. 10 UNF
    071/4 UNF 071/4 UNF
    085/16 UNF 085/16 UNF
    093/8 UNF 093/8 UNF
    107/16 UNF 107/16 UNF
    111/2 UNF 111/2 UNF
    129/16 UNF 129/16 UNF
    135/8 UNF 135/8 UNF
    53No. 6 UNC 53No. 6 UNC
    571/4 UNC 571/4 UNC
    Washers
    Prefix gives type of washer:
    PrefixType of washer
    WPplain washer
    WLlock washer (split-ring type)
    WNshakeproof washer (toothed type)
  • Armstrong Lever Dampers – an explanation

    I recently found an article about the Armstrong Lever Action Shock Absorber as fitted to the Triumph Vitesse and other Triumph cars. The article was on the North American Singer Owners Club website.

    The Armstrong Lever Action Shock Absorber

    The Armstrong New Super Double-Acting Self-Regulating Hydraulic Shock Absorber is of the Vertical Cylinder Type. All working parts are submerged in oil.

    Construction

    The body A is a zinc alloy die casting and bolts directly on to the frame of the car, the two cylinders B and C being connected by passages E and F. The double crank G and arm H are a force fit on serrated portions of spindle I, which rotates in the body A on generous double bearings. Connecting rods J connect the crank G to pistons K to which non-return recuperating valves N are fitted. The arm H is connected to the axle of the car link L.

    How it Works

    As the axle moves to and from the car frame, so the pistons move in and out of their respective cylinders pumping oil from one to the other. The interior of the body is filled with oil to within 3/8″ from top of cover, any shortage of oil beneath the pistons is instantly made good though the recuperating valves N.

    Cam valve (Self Regulating)

    As the car axle moves to and from the car frame the oil pumped from the compression cylinder B to rebound cylinder C or cylinders C to B, and has to pass between the taper ended valve P and scew Q, which is adjustable to offer any desired resistance to the action of the axle.

    As will be seen from the drawing the upper end of the valve F is held in contact with the cam on spindle I, which means that on fairly good roads the valve P is in its lightest setting and shock absorber gives a normal resistance–just enough–yet not too much to produce harshness, but when bad roads are encountered the spindle I oscillates and the contour of the cam depresses the tapered end of valve P further into the central port of screw Q and thereby increases the resistance of the shock absorber.

    The automatic, variable resistance obtained from the cam movement makes this shock absorber entirely self-regulating, the resistance automatically increasing as required thus enabling the car to pass over bad with comfort equal to good roads.

    Screw Taper Valve

    As the axle moves towards the frame the oil is pumped from the cylinder B to cylinder C, but as it has to pass the spring loaded valve R a resistance governed by the tension on the spring is offered to the movement of the axle.

    On the return or rebound stroke the oil is pumped from cylinder C to cylinder B, and as the ball valve only opens in one direction the oil must now find its way to cylinder B past the taper screw S, which is adjustable to offer any desired resistance to the rebound of the car spring.

    Adjustment of the Cam Valve

    Both rebound and compression are controlled by screw Q, to tighten rebound and compression slack nut T, taking care that the screw Q does not turn. Turn screw Q half a turn inwards and lock up the nut, taking care the the screw Q does not turn.

    To reduce the resistance follow the above instructions, but turn screw outwards.

    Screw Taper Valve Adjustment

    Both rebound and compression are controlled by screw S.
    The same instructions apply as for cam valve, but refer to screw S and nut U.

    Note.–Shock absorbers adjusted too lightly make your car feel harsh and hard; we recommend slacking off first in case of doubt.
    These shock absorbers will only work satisfactorily on Armstrong Super Shock Absorber Oil. Examine your shock absorber oil lever regularly. The correct level is 3/8″ from top of cover.

    Double Note: I personally have found these shocks to be quite reliable and I have been able to resurect several of these by just general cleaning and fresh oil. You should try that first prior to sending it out for rebuilding.

    ————————————————

    Adjustable dampers

    I had heard these existed and have now found a picture. These can be adjusted on the car without taking them apart.

    MG works adjustable Armstrong lever arm dampers
    MG works adjustable Armstrong lever dampers

    Period adjustable shock absorbers often feature in accessory catalogues and go faster guides.

    Due to the rarity of original adjustable lever arm dampers there are now firms remanufacturing and converting original dampers to be adjustable.  One instance is for the MG Sprite with items made in the USA by Peter Caldwell, in Madison, Wisconsin being sold in the UK through http://www.petermayengineering.co.uk/.

    Adjustable Dampers Autocar17 October 1968
    Adjustable Dampers Autocar17 October 1968

    —————————————————-

    Non adjustable dampers

    Adjusting the units: There is a large hex head ‘nut’ at the bottom of the units, this can be unscrewed to remove the damper assembly, take care of the ‘O’ ring. As below:

    The damper assembly looks as below when assembled:

    Armstrong lever arm damper assembly
    Armstrong lever arm damper assembly

    The little washers between the large diameter coil spring and the valve body set the preload on the BUMP damper valve. So add more washers to get more BUMP damping, try one or two washers at a time, you can easily find washers of similar id and od, if not file some.The little nut that compresses the smaller inner coil spring controls the REBOUND damping. This nut is soldered on its thread to stop it moving, easy to unsolder and resolder. Screw this nut in increases the REBOUND damping. Try one turn at a time, it is quite sensitive.

    Do both together, clamp them together in a vice, then by hand pressure on the end of the levers you can compare their resistances to get them both similar.

    Refit to car and test. Hours of fun there then!

    Rebound valve adjustment starting point ~ compress back of the car and release, eg kneel on bumper and get off the suspension should return the car to static ride height and no more. It should not bounce beyond static ride height.

    Bump damping adjustment ~ although it is ideal to set this low to get minimum vertical upward acceleration that you feel through your seat/spine. Ideally set bump damping as low as you can to prevent bouncing after a series of bumps or wallowing after quick steering inputs.

    Borrowed from a Morgan website.

    ———————————————-

    Lever Arm Oil

    Armstrong sold their own special grade of oil specially for lever arm dampers. What should be used now?

    Motor bike shock absorber oil seems to be the recommended substitute. It is available in several different viscosities. 20 as used in older bikes is what can be used. Modern lighter grades will not be stiff enough. Stiffer oil such as 30 may damage the seals.

    Some people have successfully used trolley jack oil. However it has been said such oil may suffer from foaming when dampers work hard and quickly – just when you want the damping action.

    ——————————————————————–

    Simplied later design

    Original Armstrong lever arm damper assembly with o-ring
    Later simplified Armstrong lever arm damper assembly without o-ring

    According to Alex Pringle on the TR Forum: The old Armstrong Company merged with James Lyon in the early 1970s, and considerable change resulted.

    Lever arm shock absorbers, as we think of them, had numerous and varied commercial and industrial applications . . . . automatic door closers being the most often noticed. The old Armstrong company thought of all of these items as appropriate for reconditioning, whereas the new company preferred to simplify (and cheapen) designs – and to abandon reconditioning in favour of straight replacement.

    Lever arm shocks manufactured post 1974 or thereabouts were of the simplified variety, until the eventual cessation of mainstream production, towards the end of the decade.

    ——————————————————

    You tube video

    Roadholder

    This brochure produced by Armstrong explains the range of Armstrong parts available to tune car suspension. I found this document on the http://mk1-performance-conversions.co.uk/ website a great source for early Mini enthusiast. It shows the optional adjustable dampers available for Triumph cars at the time.

    Download a copy from here.

    Armstrong adjustable dampers
    Armstrong adjustable dampers

    Armstrong adjustable dampers and springs for a works Triumph Spitfire being fettled by Jigsaw classic Triumph specialists. These dampers from the 1960’s were supplied from the collection of David Pearson of Canley Classics.

    Selectaride

    Armstrong Selectaride advert from Motor Roadtests 1962

    Selectaride electrically adjustable shock absorbers with 4-position “cockpit control”. I think this alternative form of adjustability is interesting.

    Armstrong marketed electrically adjustable shock absorbers with a 4 position “cockpit control” a switch.  These dampers were an ultimately unsuccessful product and were dropped by car manufacturers after they proved to be unsatisfactory in service.

    Refurbising

    Several companies offer to rebuild your old dampers including marque specialists like racestorations in the UK and Moss in the USA.  Additionally firms like Stevson Motors will bebuild units.  Stevson has a long history in this field having started out in 1944 from their base in Birmingham UK.

    Other sources

    Armstrong dampers were used on many different makes and models of cars over the years. Useful and interesting content can be found found various forums – the TR Register has covered the subject on many occasions. 

    More information

    If you have any information or images you can share to make this article more useful to other readers please get in touch via the comments to this post.

  • TR7 mystery parts

    I recently picked a load of Triumph TR7 spares parts.  Amongst the many parts are several I do not recognize. The top right object is made of hard black plastic whereas the other three are metal.  What are they?

    OK and the answer is:
     The
    2 pieces on the left are spring retainer clips for the front brake
    pads. The one at lower right appears to be a mounting cone for the
    MacPherson strut. It goes in just under the strut top mount.

     The two on the left are front brake pad retaining clips/springs
    Top right is the bumpstop for the propshaft (UKC826
    Bottom right is the top front suspension mounting cone (ULC2435)

    2 answers from helpful chaps on facebook and the club triumph forum.

  • Lucas Petrol Injection Service bulletins

    I recently got hold of copies of some service bulletins produced by Joseph Lucas about their Petrol Injection system.  I have copies of Lucas Petrol Injection Service bulletins 2,7,8,9 and 10 has anybody got the others?  I have scanned 8, 9 and 10 and will add them to my website.  In the meantime here is a copy of number 10.

    Lucas Petrol Injection Service Bulletin 10 page 1

    Lucas Petrol Injection Service Bulletin 10 page 2

    .

  • TR7 Strut braces

    A recent exchange on the Club Triumph forum lead to me having a look into TR7 strut braces.  I have seen them for sale on eBay and some traders such as S & S Preparations and Robsport sometimes have used ones for sale.

     Made by Andy Healey http://andystr7blog.blogspot.co.uk/

    TS Imported Automotive Triumph TR8 Srut brace

    Seen (10-11-2013) this on a USA trader site http://www.tsimportedautomotive.com/

    The Wedge Shop another USA based trader http://www.thewedgeshop.com/ stock this interesting looking version (10-11-2013).

    Demon Tweaks used to sell a TR7 strut brace but it appears that it currently listed as NLA no longer available.  Beans http://www.tr7beans.blogspot.co.uk/ has one fitted to his car.

    Beans TR7 strut brace 05/2010

    Interesting threads: http://www.forum.triumphtr7.com/topic.asp?TOPIC_ID=12644&SearchTerms=struct,brace

    Struct brace in Triumph TR7 Sprint.

    Struct brace in Triumph TR7 Sprint.
    TR7 V8 Strut brace - Christoper Kenneth Smith - V8

    Christopher Kenneth SMITH on the TR Register has the above fitted to his TR7 V8.

    John Walsh fabricated a very comprehensive brace in his 1981 Buick V6 engined car.

    John Walsh TR7 Buick V6 Struct brace

    01 December 2015 –
    From a very modified car built in the USA comes this strut brace.

    Another TR8 V8 modified car hot rodded by D&D fabrication – as owned by Eric Graves in the USA

    20 July 2016 –
    A modified Sprint engined car in the Queensland Australia owned by Matthew Taylor, showing the shiny brace. One from a small batch made in Sydney.

    This one is based on a VW Golf GTI strut brace.

    John Metcalfe VW Golf GTi strut
    John Metcalfe VW Golf GTi strut

    Australian alumiumTR7 strut brace.

     

  • Swapping out the heater and mystery wiring

    TR7 dashboard area showing interior with heater out
    TR7 dashboard area showing interior with heater out

    This morning I got the heater out.  A quick call to Rick at S&S Preparations showed that I had missed a couple of fastening that go throu the bulkhead.  To be fair they were covered in a layer black stoneguard so were not easy to see.

    Getting to the heater box has meant taking all the fascia out.  To get the fascia out had remove the lots of other stuff/trim: the a-post covers, the switch panel, the gear lever console, the steering wheel, the instrument panel, the drivers seat. As my car had various extra had to disconnect the radiator fan override, some of the radio wiring, disconnect the oil pressure gauge from the bottom of the fascia.

    Hidden ignition switch and green radiator fan over-ride switch
    Hidden ignition switch and green radiator fan over-ride switch

    Whilst the car is in this state I will able to investigate the mystery extra wiring.  There is a hidden key/ignition switch which is wired into the ignition loom – trouble is I do not have the key – the switch was well hidden I only found it when I was in the footwell looking up.  The flick switch to the left of the steering is still a mystery – it is linked into the radio wiring – which is a really complex bunch of colored wires – think I will leave that alone as it works.  Intend to add a proper separate earth for the radio rather than continue to relay on it being lopped into the earth on the back of the rheostat.

    oil pressure gauge and mystery switch no2
    oil pressure gauge and mystery switch no2

  • TR7 Wiper blade fitting

    Triumph TR7 wiper blade fitting
    Triumph TR7 wiper blade fitting

    I need to fit new wiper blades but most traders now only stock click fit style.  As can seen from the picture above the TR7 wiper blades attach via a pin.  The TR specialist I contacted did not have any in stock –  I saw some advertised on eBay which promised to include a fitting kit and were advertised to fit TR7 so I ordered them. Unfortunately the was no fitting kit so still no fix.. Am waiting for the eBay trader to sort it out. Have put up this post so I can refer them to the picture to show them the problem.

  • Repairing Jaeger & Smiths Speedometers

    I have heard from Anthony Rhodes that he has some new material and is thinking of writing a second edition of his guide Repairing Jaeger and Smiths Speedometers.

    I have a copy of a Repairing Jaeger and Smiths Speedometers on my website. You can download from Repairing-Jaeger-and-Smiths-Speedometers.pdf